Small
Animal Ventilators, CO2 Monitors, Accessories and more
SAR-830
Series Small Animal Ventilators
SAR-830/AP small animal ventilator.
Economical and reliable pressure or volume-cycled
ventilator for mice, guinea pigs, rats, cats,
dogs. Widely copied, but this is the
original!
MRI-1 Ventilator
The MRI-1 Ventilator is a small animal ventilator designed for use in MRI and other high magnetic field environments. The system comprises a microprocessor-based control unit and a set of remote, pneumatically operated, non-magnetic valves. The MRI-1 can operate by itself or can be controlled and/or monitored by a computer.
MicroCapStar CO2 Monitor
The microCapStar End-Tidal Carbon Dioxide Analyzer provides accurate end-tidal or continuous measurement of expired CO2 in animals as small as mice. It features very low sample flow requirements, rapid response time, and long-term stability. Respiratory rate (RR) is computed using the excursions of the CO2 waveform. The CO2 and RR measurements, as well as a trend plot of the end-tidal values, are displayed on the graphics LCD screen.
Capstar
C02 Analyzer for Rats and Mice
The CAPSTAR-100 Carbon Dioxide Analyzer
provides
continuous measurement of expired CO2 over the
range 0-10 percent. Its rapid response time, small sample flow requirements,
and long-term stability make it ideal for respiratory gas measurement of rodents
and larger animals.
MM-100
Metabolic Monitor System The MM-100
Metabolic Monitor System measures oxygen consumption
(VO2) and CO2 production (VCO2) of small animals
using the open circuit technique.
Gemini
Respiration Monitor
The GEMINI Respiratory Monitor measures
breath-by-breath oxygen and carbon dioxide concentration for accurate respiratory
status assessment. The instrument uses the latest technology fast infrared (CO2)
and paramagnetic (O2) measurement cells for unsurpassed accuracy and long-term
stability.
Accessories
Flowmeter/Regulators
A regulated flow source is required for each external valve assembly attached
to an SAR-830.
Rotameter-type flowmeters are available as single units or as four-flowmeter
manifolds (seen at
right). The flowmeter manifolds can be used to mix anesthetic gasses, or as independent
flowmeters
for multiple valve assemblies. Digital mass flowmeters are also available where
the highest accuracy
is required. A metering valve should be ordered with each digital mass flowmeter.
MVA-4
Multi-Valve Adapter
allows up to four external valve assemblies to be attached to one SAR-830 series
ventilator, for a total of five ventilator stations. Up to four
CTP-VA-1 valve assemblies can be powered by one SAR-830
ventilator; two CTP-VA-3’s, or one CTP-VA-4, due to power
supply constraints. Other configurations of the SAR-830 and its associated valve
assemblies are available on special order.
Complete anesthesia setups, including Halothane or Isoflurane
vaporizers, are also available.
CTP-VA-1
External ValveAssembly
External valve assemblies are used to expand the volume
range of SAR-830 series ventilators, or to add additional ventilator
stations. The valve assembly connects to the ventilator
through a supplied 12’ cable, and acts as a slave to the
SAR-830. The CTP-VA-1 (shown at right) is equivalent to the
standard SAR-830 internal valves, and is used to create one
or more additional ventilator stations. To connect more than one valve assembly,
an MVA-4 electrical adapter is required (see
below). A controlled flow source is required for each external valve assembly.
Tubing and connectors are supplied.
IITC Life Science
Inc.
23924 Victory Blvd Woodland Hills, CA 91367
818 710 8843 fax 818 992 5185
Copyright (c)
2007. IITC Life Science
All rights reserved.
